TQM Wheel End Part 2 – Grit Guard® Installation

TQM Training Part 2 – Grit Guard® Quiz

TQM Training Part 2 – Grit Guard® Quiz

TQM Wheel End Part 2 – Grit Guard® Installation TQM Training Part 2 – Grit Guard® Quiz

Time limit: 0

Quiz Summary

0 of 12 Questions completed

Questions:

Information

You have already completed the quiz before. Hence you can not start it again.

Quiz is loading…

You must sign in or sign up to start the quiz.

You must first complete the following:

Results

Quiz complete. Results are being recorded.

Results

0 of 12 Questions answered correctly

Your time:

Time has elapsed

You have reached 0 of 0 point(s), (0)

Earned Point(s): 0 of 0, (0)
0 Essay(s) Pending (Possible Point(s): 0)

Categories

Not categorized 0%

1
2
3
4
5
6
7
8
9
10
11
12

Current
Review
Answered
Correct
Incorrect

Question 1 of 12

1. Question
How many levels of inspection are involved in TMC RP-631B?
- One
- Two
- Three
- Four
Correct

Incorrect
Question 2 of 12

2. Question
What are the three main lubricants being used today in wheel ends?
- Mineral Oil, Synthetic Oil, Grease
- Oil, Semi-Fluid Grease, Hard Pack Grease
- CD-50, SF-90, 007
- Margarine, Butter, “I can’t believe it’s not Butter”
Correct

Incorrect
Question 3 of 12

3. Question
If High Temperatures are noticed during inspection, what are the usual causes?
- Tire Pressure and Wheel Alignment
- Over tightened Hubcap bolts
- Bearing Adjustment, Low lube levels, Contaminated lube
Correct

Incorrect
Question 4 of 12

4. Question
A LEVEL II inspection should be done:
- Annually
- Annually or every 100,000 miles whichever comes first
- Every two years
- Whenever it’s convenient
Correct

Incorrect
Question 5 of 12

5. Question
A LEVEL III inspection is:
- Done every three years
- To Check Oil Levels
- Only performed on Semi-Fluid Grease wheel ends
- Done with a Torque Wrench
Correct

Incorrect
Question 6 of 12

6. Question
Bearing Adjustment is checked by:
- Using a tire bar to lift the wheels up and down
- Using a dial indicator
- Looking at metal color
- All of the above
Correct

Incorrect
Question 7 of 12

7. Question
STEMCO Grit Guard wheel seals are installed:
- After applying a thin coat of #2 sealant to the OD of the seal and the spindle shoulder
- By driving a wear ring on the spindle shoulder with a STEMCO Universal Axle tool
- By driving the wheel seal into the Hub with a STEMCO Hub tool
- All of the above
Correct

Incorrect
Question 8 of 12

8. Question
Silicone should be installed around the ID and OD of the Grit Guard Seal?
- True
- False
Correct

Incorrect
Question 9 of 12

9. Question
STEMCO ProTorq and ZipTorq spindle nuts are:
- Adjusted using the same procedure
- Adjusted using TMC RP-618
- Adjusted to .001”- .005” end play
- A & B
- A & C
Correct

Incorrect
Question 10 of 12

10. Question
Spindle Shoulders and Hub Bores should be cleaned to remove contamination, rust, and burrs with:
- Emery Cloth
- Metal file
- Grinding Wheel
- Parts washer
Correct

Incorrect
Question 11 of 12

11. Question
If Semi-Fluid grease is used in a wheel end, the proper fill level is:
- Top of the outer bearing cup
- Fill the Hub full
- 3-9 O’clock, or ½ full
- Filled until it runs out on the floor
Correct

Incorrect
Question 12 of 12

12. Question
Hubcap bolts should be torqued to:
- Whatever the Drill Driver goes to
- As tight as possible
- With an impact wrench
- 12 – 16 ft/lbs with a torque wrench
Correct

Incorrect

It appears you are offline - this application will store visited pages for offline viewing.

;

Search

Congratulations!

You finished Part 1 of the TQM Wheel End Training course. To continue to the Part 2 TQM Wheel End videos, please click one of the TAKE COURSE buttons below.

To rewatch the Part 1 TQM Wheel End Video, close this pop-up by clicking the X in the top right corner.

To return to the home screen and select another video, click BACK TO STEMCO UNIVERSITY.

Has Prerequisite

A man applying grit guard to a wheel end

TQM Wheel End Part 2 – Grit Guard® Installation

Requires TQM Wheel End Training Part 1

Has Prerequisite

A man installing a Guardian HP Wheel Seal

TQM Wheel End Part 2 – Guardian® HP Installation

Requires TQM Wheel End Training Part 1

Has Prerequisite

a man in front of an unassembled wheel bearing

TQM Wheel End Part 2 – Discover®/Voyager® Installation

Requires TQM Wheel End Training Part 1

Back to Stemco University

Login

IMPORTANT: Due to the recent website updates on August 11, 2020, you will need to reset your account password before logging in. Please reset your password here. If you have any problems please contact us.

If you created an account before August 11, 2020 and are unable to login with an e-mail, please reach out and a representative will help recover your account.

We apologize for any inconvenience.

Accessing this course requires a login. Please enter your credentials below!

Username or Email Address

Password

Remember Me

Lost Your Password?